Edge Banding Machines

Edge Bander with Pre-Milling and Corner Rounding

Adds a contour-tracking unit that rounds the tape at all four corners of the panel. Doors and drawer fronts come off the machine finished, with no hand filing.

Stations
9: pre-mill to buff
Feed speed
16–23 m/min
Panel thickness
9–60 mm
Edge tape
0.4–3 mm
Machine length
6.7 m
Total power
17 kW

Test-cut at the factory before shipping. Sea freight worldwide, with remote or on-site installation.

What corner rounding adds

After end trimming, the tape still has a sharp corner at each end of the panel. On a carcass side nobody sees it. On a door or drawer front it has to be rounded, and by hand that takes longer than the banding itself. The tracking unit follows the panel corner with a small cutter and rounds it in the same pass.

Where it fits

Shops making doors, drawer fronts, shelves and any part where the banded corner is on show. Thick 2–3 mm tape benefits most.

What's on the machine

Glue pot on an edge bander

Glue pot

Hot-melt glue is kept at temperature and rolled onto the panel edge in an even film just before the tape meets it.

Edge tape reel table

Tape reel table

A full coil of edging sits on the reel table and feeds into the machine automatically. Changing tape means swapping the coil.

Dust extraction hoses on the trimming units

Dust extraction at each unit

Every milling and trimming unit has its own extraction hood and hose, which keeps chips off the glue line and the track.

Edge bander touchscreen

Touchscreen control

Stations, feed speed and glue temperature are set on the touchscreen, and saved settings can be recalled for each tape type.

Typical configuration. Final specifications are confirmed in your quotation and can be adapted to your sheet size and power supply.

Stations, in order

  1. Pre-milling
  2. Gluing
  3. Pressing with six rollers
  4. Front and rear end trimming
  5. Rough trimming
  6. Fine trimming
  7. Corner rounding
  8. Scraping
  9. Buffing

Capacity

Panel thickness
9–60 mm
Minimum panel width
60 mm
Minimum panel length
60 mm, or 200 mm with pre-milling on
Edge tape thickness
0.4–3 mm
Feed speed
16–23 m/min

Machine

Dimensions (L × W × H)
6720 × 960 × 1600 mm
Total power
17 kW
Air pressure
0.6 MPa
Boards
MDF, particle board, plywood, melamine-faced board, flat solid wood, aluminium honeycomb board

Options

Added at the factory when your machine is built.

Return conveyor

Brings each panel back to the operator, so one person can feed and stack.

PUR glue system

For moisture-resistant bonds in kitchens and bathrooms.

Second glue pot

Keep two glue colours ready and switch without cleaning.

Voltage and plug

Built for your country's supply, for example 220 V / 60 Hz.

How it compares with the other models

ModelPanel thicknessFeed speedBest for
Compact Automatic Edge Bander 9–60 mm 16–23 m/min Small shops banding a few hundred edges a day
Edge Bander with Pre-Milling 9–60 mm 16–23 m/min Shops that want a tight glue line on every panel
Edge Bander with Pre-Milling and Corner Rounding this model 9–60 mm 16–23 m/min Doors and visible fronts that need rounded corners
Edge Bander with Dual Glue Pots 9–50 mm 16 / 18 / 23 m/min Shops switching between light and dark edging every day
High-Speed Edge Banding Machine 9–60 mm 18 / 23 / 28 m/min Factories banding all shift at up to 28 m/min
Laser Edge Banding Machine 9–60 mm 18 / 23 / 28 m/min Premium fronts where no glue line may show
45° Bevel Edge Banding Machine 18–25 mm 12 m/min Handle-free doors with a 45° beveled edge

Common questions

Which edging materials can it apply?

PVC, ABS, melamine and veneer edging in coils. The tape thickness range for each model is listed in the specifications.

Which glue does it use?

EVA hot-melt glue as standard. A PUR glue system can be fitted for kitchens, bathrooms and other damp environments.

What is the smallest panel it can band?

It depends on the model and on whether pre-milling is switched on. The minimum panel size is listed in the specifications.

Can I see the machine running before I pay the balance?

Yes. Every machine is run at the factory before packing, and you can join a video call to watch your own machine band test panels.

Get the price of the Edge bander with corner rounding

Tell us what you make and roughly how many sheets you cut per day. We reply within one working day.

What you get back
A recommended configuration, FOB or CIF price and lead time.
Useful to include
Sheet size, board types, your power supply and any machines you already own.
Want to see it first?
Ask for a video call from the factory floor.

We only use your details to answer this request. Privacy policy